Mosfet Nano HARD Gate

calcActive())">
2 reviews
Mosfet Nano HARD Gate is a programmable multifunctional AEG module.
The package includes:
- Mosfet NanoHARD
- Deans-T connectors
- Simple signal cable for trigger contact
- Double signal cable for trigger contact
- Programming button
- Jumper (2 pcs)
Mosfet HARD Gate functions
MOSFET
Do you want to achieve a higher ROF and faster trigger response? Are you planning a power upgrade of your gun? In that case, you need a MOSFET.
It targets the energy from the battery directly to the motor, bypassing the mechanical trigger contacts. As a result, you gain a higher ROF of the gun and a faster trigger response.
BATTERY PROTECTION
Protection against Over-Discharge of the Battery. Modern LiPo and LiFe batteries are very sensitive to over-discharge. If you do not want to damage the battery and you care about its service life, this protection is indispensable. The microprocessor monitors the battery voltage constantly. When the voltage drops down to a critical level, it will not allow firing.
DEBOUNCING
This option offers full compatibility with micro-switches. Provides resistance to bounce contact. You get a bigger ROF, a faster trigger response, and the mosfet is less prone to overheating.
GENERATION and 3a MOSFET
The advent of modern transistors and microcontroller has enabled intelligent, small and reliable micro-mosfets to be built.
ON/OFF ACTIVE BRAKE
The Controller provides the opportunity to decide if the user wants to use the Active Brake function through the ON/OFF button. It will lead to improving the lifespan of the motor.
ACTIVE BRAKE
In SEMI Mode, the brake does not allow for compressing a piston after a shot. The piston will stop in the front position which eliminates unnecessary stresses, increasing the service life of the gearbox and its parts. This is important, especially with an AEG power upgrade. After releasing the trigger, the rifle immediately stops firing.
SMART FUSE
We have developed an electronic fuse with an accurate current sensor. A combination of current, voltage and temperature measurements makes your AEG installation highly reliable. It protects the MOSFET against overheating, overloading and short-circuiting. If your airsoft gun becomes jammed, the function protects the motor and battery against damage.
14.8V LI-PO READY
The drop-in module can be used with batteries up to and including 14.8V LI-PO. The minimum operating voltage is 3V and maximum is 17V.
COATING
Thanks to its special conformal coating, our product is resistant to atmospheric conditions (Military Specification MIL-V-173C).
BUILT-IN SELF-TEST
This allows you to quickly check whether the drop-in module is working properly. It helps to locate where the problem lies when anything goes wrong.
NOTE! We do not offer warranty for mosfets mounted outside our service.
In stock
- Product code
- 7925
€43.62
Description / Mosfet Nano HARD Gate
Mosfet Nano HARD Gate is a programmable multifunctional AEG module.
The package includes:
- Mosfet NanoHARD
- Deans-T connectors
- Simple signal cable for trigger contact
- Double signal cable for trigger contact
- Programming button
- Jumper (2 pcs)
Mosfet HARD Gate functions
MOSFET
Do you want to achieve a higher ROF and faster trigger response? Are you planning a power upgrade of your gun? In that case, you need a MOSFET.
It targets the energy from the battery directly to the motor, bypassing the mechanical trigger contacts. As a result, you gain a higher ROF of the gun and a faster trigger response.
BATTERY PROTECTION
Protection against Over-Discharge of the Battery. Modern LiPo and LiFe batteries are very sensitive to over-discharge. If you do not want to damage the battery and you care about its service life, this protection is indispensable. The microprocessor monitors the battery voltage constantly. When the voltage drops down to a critical level, it will not allow firing.
DEBOUNCING
This option offers full compatibility with micro-switches. Provides resistance to bounce contact. You get a bigger ROF, a faster trigger response, and the mosfet is less prone to overheating.
GENERATION and 3a MOSFET
The advent of modern transistors and microcontroller has enabled intelligent, small and reliable micro-mosfets to be built.
ON/OFF ACTIVE BRAKE
The Controller provides the opportunity to decide if the user wants to use the Active Brake function through the ON/OFF button. It will lead to improving the lifespan of the motor.
ACTIVE BRAKE
In SEMI Mode, the brake does not allow for compressing a piston after a shot. The piston will stop in the front position which eliminates unnecessary stresses, increasing the service life of the gearbox and its parts. This is important, especially with an AEG power upgrade. After releasing the trigger, the rifle immediately stops firing.
SMART FUSE
We have developed an electronic fuse with an accurate current sensor. A combination of current, voltage and temperature measurements makes your AEG installation highly reliable. It protects the MOSFET against overheating, overloading and short-circuiting. If your airsoft gun becomes jammed, the function protects the motor and battery against damage.
14.8V LI-PO READY
The drop-in module can be used with batteries up to and including 14.8V LI-PO. The minimum operating voltage is 3V and maximum is 17V.
COATING
Thanks to its special conformal coating, our product is resistant to atmospheric conditions (Military Specification MIL-V-173C).
BUILT-IN SELF-TEST
This allows you to quickly check whether the drop-in module is working properly. It helps to locate where the problem lies when anything goes wrong.
NOTE! We do not offer warranty for mosfets mounted outside our service.
The package includes:
- Mosfet NanoHARD
- Deans-T connectors
- Simple signal cable for trigger contact
- Double signal cable for trigger contact
- Programming button
- Jumper (2 pcs)
Mosfet HARD Gate functions
MOSFET
Do you want to achieve a higher ROF and faster trigger response? Are you planning a power upgrade of your gun? In that case, you need a MOSFET.
It targets the energy from the battery directly to the motor, bypassing the mechanical trigger contacts. As a result, you gain a higher ROF of the gun and a faster trigger response.
BATTERY PROTECTION
Protection against Over-Discharge of the Battery. Modern LiPo and LiFe batteries are very sensitive to over-discharge. If you do not want to damage the battery and you care about its service life, this protection is indispensable. The microprocessor monitors the battery voltage constantly. When the voltage drops down to a critical level, it will not allow firing.
DEBOUNCING
This option offers full compatibility with micro-switches. Provides resistance to bounce contact. You get a bigger ROF, a faster trigger response, and the mosfet is less prone to overheating.
GENERATION and 3a MOSFET
The advent of modern transistors and microcontroller has enabled intelligent, small and reliable micro-mosfets to be built.
ON/OFF ACTIVE BRAKE
The Controller provides the opportunity to decide if the user wants to use the Active Brake function through the ON/OFF button. It will lead to improving the lifespan of the motor.
ACTIVE BRAKE
In SEMI Mode, the brake does not allow for compressing a piston after a shot. The piston will stop in the front position which eliminates unnecessary stresses, increasing the service life of the gearbox and its parts. This is important, especially with an AEG power upgrade. After releasing the trigger, the rifle immediately stops firing.
SMART FUSE
We have developed an electronic fuse with an accurate current sensor. A combination of current, voltage and temperature measurements makes your AEG installation highly reliable. It protects the MOSFET against overheating, overloading and short-circuiting. If your airsoft gun becomes jammed, the function protects the motor and battery against damage.
14.8V LI-PO READY
The drop-in module can be used with batteries up to and including 14.8V LI-PO. The minimum operating voltage is 3V and maximum is 17V.
COATING
Thanks to its special conformal coating, our product is resistant to atmospheric conditions (Military Specification MIL-V-173C).
BUILT-IN SELF-TEST
This allows you to quickly check whether the drop-in module is working properly. It helps to locate where the problem lies when anything goes wrong.
NOTE! We do not offer warranty for mosfets mounted outside our service.
More Information
Product code | 7925 |
---|---|
Manufacturer / Brand | Gate |
Reviews (2)
Customer Reviews
5
5 out of 5 stars
100%
of customers
recommend this product
recommend this product
5 stars
2
(100%)
4 stars
0
(0%)
3 stars
0
(0%)
2 stars
0
(0%)
1 star
0
(0%)
Sort by
Rating
Newest
Helpfulness
Thank You For Voting!
Sebi Negescu
Jun 7, 2025
Verified Buyer
I recommend this product
L am instalat cu foarte multe batai de cap din cau...
L am instalat cu foarte multe batai de cap din cauza lipsei mele de dexteritate cu lipitu.
Intru un final l am scos, functiona dar am stricat contactul, ori se bloc ori nu mergea.
Ce nu inteleg daca e normal, da ceva mai mult scanteie la motor cu mosfetul instalat( am vazut si labunbaltul instalat de mine ) este normal?
Add Comment
Testos
Sep 16, 2022
Verified Buyer
I recommend this product
Destul de maricel ca marime.
Destul de maricel ca marime. Este usor de instalat si programat. Functia active brake se poate opri pentru protectia motorului si are si functie de protectia a bateriilor Li-ION/LiPo.
Add Comment
Product Questions (1)
Product Questions
focusElement());"
class="btn btn-primary ml-2">
Buna !
Acest mosfet este compatibil si cu bateriile Nimh 8.4 respectiv 9.6 v ?
As vrea sa il iau dar sa raman cu configuratie nimh. Merci anticipat
Acest mosfet este compatibil si cu bateriile Nimh 8.4 respectiv 9.6 v ?
As vrea sa il iau dar sa raman cu configuratie nimh. Merci anticipat
Question by: SEBI NEGESCU on Jun 1, 2025, 12:03 PM
Buna ziua,
Da, este compatibil.
Da, este compatibil.
Answer by: Service Oqtagon (Admin) on Jun 2, 2025, 3:05 PM
focusElement());"
class="mt-2 aw-pq__question-answer-form-visibility-button">